Tuesday, January 24, 2017

Limp Home U0101 et al...

Just doing my errands, heading home from the grocery store and what do I see but the return of the wrench and engine lights along with the RPMs leaping as the engine decides that limping home is the best way home. Fortunately, we were just a few miles from casa del 500 dinero coche, on roads where the top practical speed stays below 35MPH, so no biggie.  Can't say my passengers were all that happy, even though the car performs well most of the time, they expect to be stranded for every outing.

I was able to get the codes from the car using the Android “FordSys” program (more on that later), here’s what I have:

Code
Meaning
U0101
Lost communication with TCM (transmission control module)
P0641
Sensor reference voltage ‘A’ circuit open
U0415
Invalid data received from ABS (anti-lock braking system) module
U1900
No description
B1318
Battery voltage low
B1342
Electronic control unit is faulted

After letting things rest (and the super-cap drain so things reset), the engine started no problem, no wrench light and the check engine light turned off after the second engine running cycle, just like the last time this problem occurred.

Sometime a few months ago, I broke down and laid-out the $29, or something like that, for an AllData DIY subscription for the Freestyle. For the error codes in question, there’s a bunch of “pin point” tests to check for continuity and wiggle checks for the connectors.  What All Data doesn't provide the full schematics for the car, as I'd like to see where +5v circuit A goes, as I have an intermittent issue with some segment of that wiring it seems.

Looking at the codes above, I’m guessing a short or disconnect (somewhere?) resulted in a few components going into reset due to a voltage drop or the networking between the components failed due to signal integrity. Before replacing parts, I need to make sure the communication between said parts works properly, or I won't be fixing the problem by swapping what's at either end of a bad connection.  I’m presently replacing the brake lines on my kid’s Grand Am, so the actual checking will need to wait for a bit.

FordSys

All of the diagnostic information comes to me complements a program on my Android phone called FordSys. A regular code-checking program returns no problem codes, because what’s reported above aren’t in the standard inventory of codes for engine trouble a generic code reader reads. I very much like FordSys, I’m not so crazy about the intrusiveness of the ads.What was small ads on the bottom of the screen has morphed into full screen overlay ads. I’d much rather pay the developer, who deserves the money for his hard work, and not be bothered with ads at all.

Wednesday, January 18, 2017

290,000 mile mark; on to 300,000

More like 290,0017 mile mark, just 10,000 miles shy of 300,000 miles.   At my current driving pace of ~625 miles per month, that's about 16 months away, I think I can eek out that much life from the Freestyle to cross the 300,000 line.  It's the next 33,333 miles to get me to 333,333 miles that's questionable.

I'm hoping for a few road trips this spring/summer to pad the odometer.  Onward!

Tuesday, January 17, 2017

Happy (belated) new year!


After Christmas, we headed out to Birmingham, AL, mostly because I hadn't been there and my wife refused to visit Paducah, KY.  Why Paducah?  Not really sure, but the city's own website highlights the bridge out of town, that should be telling enough. Hadn't been there either, not really sure why anybody wants to stay there, but I did find out, while watching NOVA, that Paducah has a large scale storage facility for nuclear waste, so it has that going for it.


By (Earthsound) / (flickr profile) - Own work, CC BY-SA 3.0, https://commons.wikimedia.org/w/index.php?curid=16873493
Vulcan
The largest cast iron statue, Vulcan, resides in Birmingham.  The work itself can be found atop a hill in sturdy park that has the look of a WPA project -- The kind of public works the U.S. desperately needs but no longer undertakes. Unfortunately, the pedestal on which the sculpture rests was the victim of a late 1960's improvement where an elevator shaft was installed directly in front of the pedestal, obstructing the view of the original architecture and visually competing with the structure from nearly every angle. The impressive fountains were replaced by grass and the statue itself was actually painted dirt red.  A complete disaster for such an impressive work of art.  In the 2000's the statue was refurbed (as the picture shows) but the terrible elevator shaft remains; hopefully, somebody will get the sense to tear it down.

Returning from Birmingham, I was sent to San Francisco; actually, Sunnyvale, which is an edge city with who's primary resident is Google along with a smattering of other high-tech companies of all flavors.  While in Sunnyvale, I had lunch at a place called Barn Thai, who's decor was decidedly un-barn like, I think "barn" might not mean "barn" as in Pottery Barn, or maybe it does and the decor was just that bad. Despite the confusing name, the food was excellent.

As we were leaving lunch, I spotted this gem of a Chevy Astro van:





Not really sure why the owner was decorating his van as such.  The group I was with thought this was a soccer fan, but the appearance of several bicycles didn't seem to jive with that theory. I would have liked to get some better pictures, but all I had was my cell phone and we were running late by the time we left.

Car problems; or, lack thereof

Unlike the last time I returned from CA, when my car didn't make it home from the airport due to the water pump failing, this time, the ride home was uneventful.  I was very happy because the weather was unpleasant when I landed and I wasn't much in the mood to call for another tow.  Oddly enough, I did share a flight with another pair of basset hounds.  Different than the pair before, not sure what's going on here, maybe some elaborate basset hound migration scheme?  I'll have questions if I encounter another set of hounds on my next trip to SFO.

Over to the left is a picture from window of the snow covered Pittsburgh suburbs on my approach to PIT when returning home.  The prior week in Sunnyvale, temperatures remained in the low 60's, maybe in the 40's at night.  In the greater Pittsburgh area, the weather told a different story, with snow accumulation and temperatures rarely rising above the teens.

Here's the good news: I think I've reached steady-state with the mechanical condition of the Freestyle.  There's still problems with the car, but none interfering with the daily driverness of the car:
  1. Rear lift supports not working
    More of an annoyance than what would expect.  I like taking the Freestyle for grocery shopping as the flat folding back seat is great for loading the bags.  To use the back gate, I need to balance the door on my back while loading/unloading.  I think I'll tackle this next.
  2. Exhaust leak
    A small leak has blossomed into a more agricultural exhaust note.  The sound seems to be emanating from the far side of the catalytic converter, so I'll just need an resonator and muffler. I hope.  Working under a car tickles some deep-seated entrapment fears, I'll need to get other these to fix this problem.
  3. Air conditioning system recharge
    The compressor failed, resulting in the accessory belt breaking regularly.  While no article has been written on the subject, I replaced the compressor and while I was at it, the rest of the A/C system.  The system hasn't been recharged, I task I felt could wait until the arrival of warmer weather.
  4. Transmission not shifting smoothly
    The symptom I'm seeing is the transmission not wanting to shift into glide or sometimes not up-shifting, as much as that concept exists in a CVT.  I've found putting the car into neutral and letting is drift for a little will result in the return to correct behavior.  The weird thing: the RPMs  don't drop below 2000 when in neutral in this state, so we might not be seeing a transmission problem per se.
  5. Airbag light
    This turned on a few months ago, I need do some continuity tests to chase down this problem, as I'm not sure if the sensor failed or if the wire to the sensor failed.
  6. Traction control and ABS lights
    We have some dashboard lights for traction control and ABS.  I have the codes for these, it's   a matter of chasing them down and figuring out what's really wrong.
  7. Suspension
    The Freestyle has the factory dampeners, at nearly 300K, well past their service life.  This mildly inteferes with the handling under regular driving conditions and when a bumpy road the ride becomes, well, let say spirited.
Over the next few months, I'll be knocking things off the list as I have the time, unless something else crops-up that takes the Freestyle off the road.

Saturday, December 24, 2016

Christmas tree and a trip to the mall

We went to our local tree farm (being out in the country, there are several tree farms to pick from) to slay our Christmas tree.  The "product" of a fresh-cut tree involves climbing on a tractor, being abandoned in a field with a saw and hauling the tree home atop one's car after the tree has been baled. Wondering around in the field looking for a tree means that quite quickly, nearly all trees begin to look the same.  Only once it's home does one notice the bald spots and general crookedness of a tree that looked just fine in the field.  Buying a used car is pretty much the same experience, what looks to be great in the lot with its companions seems to loose its luster once you've gotten it home. Buyer's remorse?  Maybe it's just too difficult to process so much information at one go, so our brain fills in the details, dents and scrapes.  When we're looking at one car, we can the concentrate on the finer details.


Probably won't fall off, maybe?
 We didn't always go Christmas tree hunting, in our family, BC (Before Children, or, BCE, Before Children Existed for the folks with a knot in their kickers and variously colored hair.), we celebrated Christmas sans a tree. Having a $500 dollar car means not having to worry about dents/scratches incidental to getting the tree home, all one needs to do is heave the tree on the roof and secure it with some twine.  No padding or a tarp, just get close and lob.  It wasn't always like this, when we drove an overpriced Honda SUV or pricey minivan, we cared about the roof.  Dents?  Scratches?  Sap? Mud? All of that used to matter when our car monthly payment approximated the purchase price of the Freestyle.

One feature of the Freestule that I just love is the raised roof rack.  This made securing the tree much easier, as I had an easy place on which to loop the twine and make knots.   In the process poorly securing the tree to the car, I looked down and what did I see by an expended hypodermic needle.  It's probably flotsam from a friendly neighborhood injectable drug user, either getting their tree or working in the fields.  Maybe a diabetic?  Most diabetics fanatically keep their sharps safe, so maybe, but unlikely.

A trip to the mall, some more Christmas lights

Limp home mode
The next day, we got the first snow of the year: better than a light dusting, maybe one or two inches. On my way to the mall, after dropping my kid off at work who didn't want to drive in the snow I felt the AWD system kick-in and then my troubles started.  The car went into "limp-home mode".  An Eat 'n Park was close by, so we stopped there for brunch and after eating we'd see if the problem went away, as stopping for a quick road-side reboot of the engine didn't help.  I didn't have my code reader handy, I'm not sure what problem occurred, but we got the combination wrench and check engine lights, as the picture shows.  This can mean either transmission, transfer case or throttle problems.

Former furniture store
Post breakfast, the engine started without an issue.  We needed to head to the mall for some shopping, which was close. If the car became cranky again, the plan was  to have the better half shop while I called for a tow.  I'd have a nice place to wait at the mall for a tow truck and would return to the mall with a working car.
My last visit to the mall was... I can't even recall when I was last at the mall, but over the years, there's been a shift from retail to personal services.  Now, however, the transition now seems to be from personal services to just empty spaces, not unlike the transition many small town's main streets in the area endured in the 1970's as retail fled main street for the mall, store fronts turned into exercise and tattoo parlors before the front windows served to hold news paper concealing the empty insides.

Earlier this year, before the retail season, Sears closed at the mall.  When the Beaver Valley Mall opened in 1970, Sears was an anchor tenant (along with Gimbels and Horne's), maintaining the same location for 40+ years: a dependable source of tools, lawnmowers,
As always, an empty lot around Sears
boots, Levi's and something polyester your grandmother would wear to a cousin's wedding.  The next biggest tenant, Macy's, doesn't look to be sticking around, as the upper floor has been closed and the range of merchandise greatly decreased.  Meanwhile, across the street, Wal-Mart's lot brimmed with shoppers.

Tuesday, December 6, 2016

Torn seal, failed water pump, back on the road

Oil from torn seal
When my new water pump failed, the ground metal from the water pump tore newly installed seal into bits, causing another oil leak.  Here's what I saw when I removed the pump from the car, over on the right.

Having replaced the very same seal before, I wasn't at all intimidated this time around. Out came the seal puller and in one swift hand-motion, I lost my grip and whacked the back of my hand against the radiator.  I was wearing my gloves, but they don't offer much protection for the back of the hand and it seems that's the most sensitive part. A little more fiddling and out came the seal. 

Torn seal
The tearing was complete, a replacement was necessary.  Getting a clear picture wasn't easy, because it was difficult to keep the background and foreground in focus, but here it is over on the left.  While the old seal apparently wore so that it wasn't keeping a tight grip on the camshaft, this one was completely compromised.  Just like the last time, I put a thin coat of oil on the seal and worked it over the camshaft, using my Craftsman Seal Seating tool (right) and a few taps from a plastic dead blow hammer to make ensure the seal was seated.

Re-attaching the water pump

New pump installed
Once the seal was back in place, I re-attached the three 8mm bolts holding the new water pump loosely and then the center 13mm bolt loosely, then tightened the outer bolts and then put more force on the inner bolt.  I'm not sure why this is the process, probably to make sure the impeller is correctly centered in the housing.  The final torque specification for the center bolt is 18 in/lbs (25nm) which is not much more than hand tight and on the lower end of my torque wrench's scale.  It didn't feel like much so I gave the bolt an extra 1/2 turn, as I wasn't sure if my wrench was accurate and I didn't want the impeller to stop working if the bolt wiggled loose.  But I didn't want to overtighten either as that could crush the seals around shaft keeping the fluid where it belongs.

All back together, recycling the coolant

When I took things apart, I used a basin to catch the coolant fluid in hopes I could use it again and not have the hassle of taking it to the disposal center (c'mon, we don't put chemicals like this down the drain, that would be uncivil) whilst saving a few bucks.  Before pouring the coolant back in the car, examination showed bits of dreck floating about, dreck I'd rather keep on the outside of the cooling system.  My solution was to put a coffee filter in the funnel and have that catch the chaff; however the filter was a bit too fine and I was a bit too impatient. 

The filter was replaced by a paper towel, and in about 10 minutes, all of the captured coolant was back in the system.  I was thinking that the ethylene glycol molecule's size was the cause of the poor flow through the filter, but I was wrong by a factor of 1000.  Our friend C2H6O2 is about half a nanometer and a the average pore size of a coffee filter is about 50 microns, so the chemical should have passed through like a bee through an open window, or air through a residential screen, even if some of the molecules clung together in the filter's mesh.  The slow speed was probably the filter doing it's job removing nasties from the fluid.

I thought I was being paranoid with the filter, but here's a picture of what remained in the pan after filtering.  And, yes, the pan was clean before it caught the fluid.  When pouring the liquid into the filter, I was careful not to disturb the sediments, as I didn't want the filter to break, or more likely, clog.

Job being done, I'm hoping that two's a charm when it comes to water pumps.  It's been about 200 miles on the new pump with no problems, so I'm not worried about the torque of the impeller bolt, or at least I'm not worried that much.